Learn How To Sharpen Your Lawn Mower

Is your lawn mower tearing of grass blades of grass instead of cutting it? Looks like your lawn as it was eaten by a goat, despite being cut by the lawnmower? Wait, do not pull your hair by the root. Help is at hand. We will teach you how to sharpen the blades of the lawnmower to minimum price and effort. Your Guide Lawn Mower – The faithful BehindsTools Walk: The tools you will need to do this work, are – you and your time of about 2 hours or less: A bastard file of about 12 "long-One Bar petty theft to prevent any movement of rotor of lawn mower. – A table will be useful for working comfortably Dong. Procedure: You can use the following procedure as a general guide and modify to your liking. Remember the procedure is not sacrosanct. The results are important, not the procedure. 1. If possible, remove the handle of lawn mower and lawn mower on the table. 2. Fix it if possible in the clamps. If you do not have clamps, do not panic, secure it against any class so that the movement away from you is limited. 3. Fix the crowbar in the blades so it will not rotate4. With the help of the bastard file, file the edges of the blades so they look sharp. Work at an angle of 45 degrees5. When a blade is sharpened, remove the crowbar and turn the rotor to work on another blade. Repeat the procedure until all blades are sharpened. 6. If you have a flexible shaft grinder in your DIY workshop, you will be able to complete the work within 5 to 10 minutes per blade. Make a template of blade profile before starting your work and compare frequently. This is necessary to make sure not to cut too much in one place. YouWhile Safety Tip To sharpen the blades so that the stroke is too long or you are injured in May Sharpening the blades of Power MowerDepending on mower the procedure may vary. We have included general statements in this procedure, you need to modify the procedure slightly. Keep the maintenance manual lawn mower handy if you have one. tools. – Siphon hose and clean container – heavy work gloves and eye-Double-cut (medium rough) flat file scrap lumber – Socket Wrench Set – Rubber Mallet *- Bench vise or C clamps – Rotary blade sharpener Accessory Electric drill or screwdriver *- 1/4-in. rod or bolt-*- Blade Balancer Blade Replacement ** Only if the list requiredThe formidable air in May, but the tools are generally available with all DIY enthusiasts. Procedure: The procedure is given for the simple single blade lawn mower, but the same will apply to all types of blades, whether single or double gloves and clean the engine and fuel tank from outside, remove the spark ignition engine – Remove all the fuel in the tank of gasoline engine. Use the siphon hose to avoid spilling gasoline on the floor. – Completely drain the oil from gearbox if you have a Invert the engine and have access to the blade. – Clamp the engine so it does not move and clean the blade area thoroughly with the help of a key box, remove the nut holding the blade. Usually, the nuts will be released in the reverse direction of rotation of the engine. You may engage the screwdriver in the cooling fan motor to stop rotation of the engine. – If you find that you are using too much force to unlock the nut, put one or two drops of rust removing chemical, and try after 30 minutes-Once you remove the blade grip in the bench vise and sharpen with a file or a grinder. Sharpen only 2 to 3 inches outside. The area to be sharpened will be known if you see the blade. – Increase to the extent necessary. Too much sharpening is not necessary. This is not the knife. It operates at the speed of the engine after sharpening, check with your thumb. Be careful not to cut thumb. If you've done sharpening before, or seen someone do it, you'll know what we mean by that. – Balance the blade with a balancing tool on VEE small blocks, or even on foot two rules placed side by side-Refit the blades, refill engine oil and gasoline and test sharp blades on uncut portion lawnSafety your advice: – Always use safety glasses and gloves when working with power tools. – Remember to remove the spark plug before starting. Serious accidents can occur if you do not do that.